March 16, 2010, 05:24:44 PM *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
News: AEM ECU Jumper/Extension Harnesses! Available NOW!!
 
Pages: 1 2 3 [4]
« previous next »
Print
Author Topic: New FIC Software V.3.04, Full Install Version  (Read 19229 times)
SB
Administrator
500+ Post Club
*****
Posts: 896
« Reply #45 on: February 02, 2009, 06:07:37 AM »
gtracer, I've attached a .zip file including all the firmware files on the first post in this thread.
Logged
gtracer
EMS Poster Child
*
Posts: 8
« Reply #46 on: February 02, 2009, 06:35:31 PM »
I'm assuming it's the FIC-6 firmware, if so thank you for your help.
Logged
gtracer
EMS Poster Child
*
Posts: 8
« Reply #47 on: February 02, 2009, 08:35:47 PM »
 :-DYep that's what I needed!  Everything worked fine and thanks again.
Logged
xxquickxx
EMS Poster Child
*
Posts: 1
« Reply #48 on: February 11, 2009, 08:47:07 AM »
What hex file should be used for an 06 eclipse GT/ with version 3.04?? I just got the car back from the shop and tuned, and installed version 3.04 off the disk.  so i can save my tuned map. I can connect to it with out any errors, but the program keeps freezing up on me, Im using vista.  Also im getting a little stutter when around 4,000 RPM at WOT

The x300 and z110???
Logged
jcat
EMS Poster Child
*
Posts: 2
« Reply #49 on: February 15, 2009, 06:14:15 PM »
I'm running the latest software and have been getting an error that the firmware z110 is out of date.  I tried reflashing per the instructions i found here and in the manual and it hangs on reading microid! in the script window, and nothing happens (for hours even).

any help here? I'm trying to get it at least up to date so itll be ready to tune after my install.
Logged
specialed
Short Bus Driver
Administrator
100+ Post Club
*****
Posts: 108
« Reply #50 on: February 26, 2009, 01:21:03 PM »
If it's getting stuck on reading MicroID, you'll most likely need to have the unit sent in to AEM to have it hard flashed. Contact the Tech Line on getting an RMA# issued to you so that you can send the unit in.
Logged
XoX1de
EMS Poster Child
*
Posts: 15
« Reply #51 on: March 28, 2009, 05:31:21 PM »
just curious, is there a new version of FIC software in development? you guys cant tell us the changelist or new feature??
Logged
cory james
EMS Poster Child
*
Posts: 3
« Reply #52 on: April 02, 2009, 09:23:59 AM »
what hex file should i use i have a scion xb 2008 it wont let me use the 104 only the 300 any suggestions
Logged
Bugermass
EMS Poster Child
*
Posts: 22
« Reply #53 on: April 15, 2009, 08:44:34 AM »
Can you guys PLEASE put in a 2D graph X axis Load and Y axis RPM.. 2D graphs for RPM vs LOAD are super super helpfull and usefull when tuning.. You ened to add is to the EMS software too.. 3D tables are much more cumbersome. 2D tables drastically cut down tuning time.
Logged
Explosivpotato
25+ Posts Club
*
Posts: 39
« Reply #54 on: April 16, 2009, 10:14:24 AM »
I don't know about you, but I'd crap my pants for 3d tables.

Logged
soxfan143
EMS Poster Child
*
Posts: 4
« Reply #55 on: April 28, 2009, 09:52:42 AM »
What hex files will I need on an 06+ Civic Si. I'm switching from the emanage ultimate tomorrow. I just recently installed v3.04 yesterday on my laptop. I'm also running Vista. What will I need guys? I do NOT want any issues. The emanage does not run with Vista so this is a great plus for this system. I'm soooo looking forward to being able to control my O2 sensor voltages with this unit as well. Thanks in advance for any input guys.

-Mike
Logged
AEM Performance Electronics Forum
   
 Logged
Pages: 1 2 3 [4]
Print
« previous next »
Jump to: